K-Tek KP16TA Mighty Boom 16' 6-Section Graphite Boompole with Coiled Cable and Transmitter Adapter Module

- KP16 Mighty Boom 6-Section Graphite Boompole -
The KP16, Mighty Boom Boompole has a collapsed length of 44" (112cm) and an extended length of 16' (4.88m) and only weighs 2.0lbs (0.9kg). This 6-section Boompole features a removable headpiece for cable reconfiguration without soldering. The top attachment is a 3/8" - 16 male thread and the bottom has a removable rubber bumper. Compatible with the KPCK16 cable kit and bottom (KPCCR) module to allow for a coiled cable option with a side XLR exit.

The New K-Tek Klassic Poles offer increased interchangeability with its removable headpiece. Gone are the soldered and sealed poles of the past. Today's redesigned headpiece, after removing a standard sized set screw, simply threads on and off the tube smoothly. The cable of choice can be removed or installed? Without soldering. The boompole is readily transformed to un-cabled, coil cabled, straight cabled or with a transmitter at the top or the bottom. There are no more time-consuming transformations and no need to purchase a completely new system just to comply with a cabling change.

K-Tek has designed poles that are more rigid and have a shorter collapsed length that is desired in today's production environment. Mighty Boom's maintain the original light weight of the tubes, yet the new design features added strength. Also, adding a sixth section and wider tubes increases the stiffness and optimizes handling balance. The result is quicker cuing and more user control of the microphone.

Another new benefit is a change to the locking collars. The traditional K-Tek captive collett has been modified with a thicker yet smoother surface allowing for more subtle, gradual extension of each section. A new anodizing process combined with changing the exterior dimples to oval divets gives a better grip and smoother feel when opening and closing each collar. The finish between the tubes has also been modified so the Mighty Boom sleekly glides open and closed. New Mighty Boom poles are hand-burnished to diffuse handling noise.

- KPCK16 Coiled Cable -
Cable Kit for 16'Mighty 6 section Boompole (KP16). Requires a bottom module (KPCCR) to work. Top of cable features the New Mighty Boompole Right Angle Low Profile 3 pin connector. The Mighty 6 section boompoles have a removable headpiece therefore no soldering is required, simply drop the cable through the top section once the headpiece is removed, plug the TA3 into your bottom right angle exit module (KPCCR) and attach to the bottom of your KP16 boompole. K-Tek's Mighty Boompole cable has thicker gauge wire and stronger shielding than previous versions.

K-Tek has created a higher quality coiled cable featuring a brand new, low profile right angle connector. The new Mighty Boompole Cable incorporates thicker gauge wiring and aluminum shielding to make it both stronger and ultra-protected from radio frequency (RF) interference. The new Mighty Boompole Right Angle connector is smaller, lighter, serviceable, and made with the popular Neutrik connector as its base. A new solid strain relief makes the Right Angle connector remarkably robust while securely holding the wiring in place. As an added benefit, the connector orientation can be changed by simply unthreading its housing, rotating it to the desired position, and locking it back in place.

The TA3 at the base of the cable is surrounded by a machined Delrin shell which secures the cable to the connector. Simply plug the TA3 into the male end of the KPCCR module. In extreme weather conditions it may be wise to unplug and remove the cable from inside the pole. Keeping the bottom open by removing the bottom module or adding the flow through base (KPFT) will allow water to drain through the pole instead of filling the inside of the tubes.

- KPTA Transmitter Adapter -
This Sidekick bottom attachment allows for the use of Mighty Boompoles with a plug on transmitter. The Male 3-pin XLR Transmitter Adapter faces up and features a removable Rubber bottom. Designed to fit Boom Pole Storage Units like the Boombox or Boom Caddy. Attaches to the bottom of any Mighty boompole. Used with plug-on wireless transmitters. Cable Kit (KPCK9, KPCK12, KPCK16, KPCK20) is needed with TA3F that plugs right into the KPTA. Once the cable kit is dropped through the top of the Mighty boompole and plugged into the module, the bottom module simply screws onto the threaded sleeve at the base of any Mighty microphone boom. No soldering needed.

The KPTA is a 5.5x3.2" (140x80mm) module of machined aluminum with the new Mighty Boompole black anodizing process for better grip and smoother feel. The Male 3-pin XLR faces up. It has a sleeve and collar on top to fit onto any of the new Mighty boompoles. (KP9, KP12, KP16, KP20). It weighs 7.7 oz (218g) which together with the wireless transmitter also functions as a counterweight to help balance the boom pole and microphone.