Pre-PMA: PocketWizard MultiMAX gets upgraded

Written by Adorama News Writer
|
Published on January 26, 2008
Adorama News Writer
Adorama ALC

versions. Based a new radio chipset, the units now have:


  • A USB Port for firmware updates
  • Enhanced close range performance – they work better when very close together
  • FAST MODE, a welcome return to the feature set
  • An improved user interface
  • Remote pre-release control – turn on or off pre-release remotely using the proper cables
  • USB Port – Firmware Updateable
  • The USB Port will be used for future firmware updates as needed. It requires a common Mini-B USB cable like those used with many digital cameras, PDAs, cell phones, MP3 players, etc. The cable is not included but is widely available.

Firmware updates will be announced on PocketWizard.com. They will be available in both MAC and PC versions. See below for instructions on finding your current firmware version.



Recent MultiMAX units without a USB port may also receive firmware updates in the future, but those models will need to be shipped to the distributor or factory for reprogramming. Older MultiMAX units are not likely to receive any more updates.



Enhanced Close Range Performance


Extreme close range operation (working distances between 1 and 3 feet) has been improved, while retaining PocketWizard’s legendary long distance capabilities. This is a benefit for users that use MultiMAX units grouped very close together like at sporting events where transmitting and receiving units may be used at the same fixed location. It is still recommended that units be a few feet apart for best performance, but these improvements increase reliability and reduce overload at close range.



FAST MODE


The latest chipset used in the MultiMAX is capable of FAST MODE, a feature that enables photographers to use faster shutter speeds with remote flash. Some units produced in 2007 lacked this feature (firmware versions 6.11 and prior 6.xx versions) while previous versions (4.xx, 3.xx) did have FAST MODE. With compatible cameras and flash units, up to 1/500 shutter speeds can be used with focal plane shutters (SLR digitals) or 1/1000 with leaf shutters.



Improved User Interface / Menus and other features


Introduced mid-2007 in the 6.xx models, the easier-to-use menus are continued in this latest MultiMAX. Previous models were marvels of programming with their rich feature set packed into a small memory space, but had to compromise on simplicity. Newer chipsets have much more memory and thus an improved UI and better features including:

  • Faster Frames Per Second handling in line with the latest SLRs (12 F.P.S. or more)
  • Hours:Minutes:Seconds display in Intervalometer mode, including countdown to next trigger
  • Low power operation in Intervalometer Mode (up to 2 weeks on a set of AA batteries)
  • Maximum times for many features increased (Contact Time, Intervalometer, Multipop, etc.)
  • Ability to use arrow keys in menus
  • Consistent numeric entry across all functions
  • Improved low battery / AC adapter detection
  • “Contrast adjustment” and “Reset to factory defaults” have their own menu items
  • Remote Pre-release Control
  • Utilizing the 6-pin ACC port and a new cable design, it is now possible to toggle on and off pre-release (like pressing the shutter button halfway) for a remote camera.

Pre-releasing a camera causes it to auto-focus / meter and it also responds more quickly and consistently. It also consumes the camera’s batteries more quickly. Previously, using older style cables, setting up the camera before an event required you to flip a hard switch that left the camera pre-released for the entire event, or until the batteries died.



Now, when you toggle on a Quad-Triggering Zone on the transmitting MultiMAX, pre-release is enabled on remote cameras set to the same Channel and Zone. Imagine setting up a camera hours before an event and not pre-releasing it until just a few minutes before it is needed. The camera’s batteries will last much longer and the entire event will be captured.



The new cables are currently being sourced and should be available mid-February. Visit PocketWizard.com for more information.



This feature is already available on 6.xx and 7.xx MultiMAX units.



Version 4.04 units with the 6-pin ACC port have a limited version of this feature. On 4.04 units, toggling any zone (including local) on or off will cause remote cameras to be pre-released, but only for 6 seconds. It may be possible to extend this time using Custom Functions in some cameras.



How to determine what you have:


Turn off each MultiMAX, hold down A, and turn it back on. It will display the installed firmware. Look at the unit and note its distinguishing features per the chart below:




ShippedDistinguishing Features FAST MODE Pre-Release Control User Interface/ Feature Set Firmware update-ability Firmware
2008A USB Port 6-pin ACC Port Yes Yes Improved Via USB by user/owner 7.xx Latest: 7.29
2007A 6-pin ACC port (no USB) Not YetB Yes Improved Distributor or Factory onlyD 6.xx
Latest: 6.11
Up to 2006A 6-pin ACC port (no USB) Yes YesC Standard Distributor or Factory onlyD 4.xxD
Latest: 4.04
Older units No USB No 6-pin ACC Yes No Standard Distributor or Factory onlyD 3.xxD
Latest: 3.28


A = Ship dates are approximate. Dealers may have new, in-warranty stock on the shelves from various times.

B = LPA is determining if a firmware solution can re-introduce FAST MODE to these units. If so, then they will need to be returned to the distributor or factory for reprogramming. Watch PocketWizard.com for information.

C = See “Pre-Release Control” above for notes on 4.04 operational differences from 6.xx-7.xx firmware.

D = Unlikely to receive future firmware improvements, however it is recommended that you bring the units up to the latest firmware available since the updates contain bug fixes. If you do not have the latest firmware, contact the distributor or factory for information on obtaining a firmware update and to assess warranty eligibility.