


See Options
2 Year
$219.99
3 Year
$349.99
5 Year
$689.99
Need help? Ask our experts.
Review Summary
Accidents happen. Protect your favorite Adorama products and purchase a protection plan to stay covered from accidental damage, mechanical or electrical failures, and more.
If we can’t fix it, we’ll replace it at no additional cost.
Protect your product from drops, spills, and more.
Enjoy your gear without fear. We have you covered!
When regular use of your product over time results in mechanical or electrical failure.
We will never charge you a deductible after the purchase of a plan.
Our claims process is simple & easy and our customer service team is happy to help.
Adorama Protect powered by Extend is available for purchase to customers in the United States. Not available for international or U.S. territories purchases. Plans on open box items do not cover pre-existing damage.
Adorama Protect plans are available for ABS clients. If you have any questions or require assistanse, please call 800-223-2500
Browse our FAQ
250W per Channel
70V
>250
6.2dBu
20k ohms, balanced
20Hz - 20KHz, (unweighted) +/-dB
>98dB
Euroblock
Ethernet
Euroblock
AC Power Switch
Individual input attenuators
Ethernet 10/100
Remote standby
Preset recall (4)
Remote Level (8)
Remote Data
Power (Blue)
Standby (Yellow)
Protect (Red)
Disable (Yellow)
Com (Green)
Bridge (Green)
Signal Level -18dB, -12dB (Green), -6dB (Yellow), Clip (Red), Temp (Yellow)
Temperature dependent speed-controlled fan (Front in, Side out)
200W
120VAC
Control via Ethernet connection with Protea NE Software
3.5 x 19 x 16.84" (89 x 483 x 428mm)
24.7 lb (11.2kg)
NE Series Amplifiers are uniquely designed around an energy-efficient Class-D platform with a switching power supply.
Connecting and controlling an amplifier for networked systems has now been simplified with Network-Enabled Amplifiers. This line offers ease of use, setup and control using standard 10/100 Ethernet protocol and Protea NE Software. No special outboard control units are needed. Choose either 4-channel ne4250 or 8-channel ne8250 amplifiers are rated at 250W per channel with separate HI-Z and LO-Z models.
NE Series amplifiers are offered in two separate platforms - the standard network amplifier or a network amplifier with an on-board Protea DSP Processor. Each can be customized for any installation by adding your choice of AES3 inputs, Dante or CobraNet card.
NE Multi-Channel amplifiers are also offered with 240V Line Voltage in either Low-Z or 100V constant voltage output models for International customers.
ne8250.70
The eight-channel power amplifier shall deliver a minimum power of 250 Watts RMS per channel into 70V loads with all channels operating. When switched into bridged-mono mode, channels 1+2 or 3+4 or 5+6 or 7+8 of the amplifier shall deliver at least 500 Watts RMS into a 140V load. The power amplifier shall include Euroblock input connectors and Euroblock output connectors. It shall have balanced analog inputs. The power amplifier shall have remote standby for power up, DC remote level control and contact closure preset recall. It shall have Ethernet control and monitoring of power functions, level, mute, polarity, temperature, current, and amplifier fault conditions.
Frequency response shall be 20Hz to 20kHz +/- 1.0dB. Signal-to-Noise shall be greater than 105dB unweighted and SMPTE intermodulation distortion shall be less than 0.5% into an 8 Ohm load, 10dB below rated output. The front panel shall provide the status of power, standby, protect, power switch disable, signal level, bridge, over-temperature, overcurrent, and Ethernet communication. The power amplifier will be capable of having factory installed AES3, CobraNet, or Dante interface options with the addition of two 4-Channel DAC cards. The amplifier shall mount in a standard 19 inch rack using two spaces (3.5. high) and weigh 24.7 pounds (11.2kg) or less.
https://ashly.com/warranty-information
800-828-6308