2025-05-23T20:00:00
Rated 2 out of 5
Needs to go back to the drawing board.
While the overall design is solid, the red dot sits too low the scope turret blocks the point of view in all mount options. An optional spacer would be beneficial.
Mark R.
Originally posted at
2025-04-02T20:00:00
Rated 5 out of 5
It's perfect. Thanks you very
It's perfect. Thanks you very much.
curtis g.
Originally posted at
2025-02-26T19:00:00
Rated 5 out of 5
Perfect. Solid addition to scope
Perfect. Solid addition to scope mount
Brad B.
Originally posted at
2025-02-20T19:00:00
Rated 5 out of 5
perfect options for my rifle
perfect options for my rifle
Isaac A.
Originally posted at
2025-01-18T19:00:00
Rated 1 out of 5
Ruined the finish on a $1. 5k scope
Ruined the finish on a $1. 5k scope. The screw are to long and went straight into the scope. I use a torque and the proper torque. I guess I'm never reselling that scope.
Russ
Originally posted at
2024-12-08T19:00:00
Rated 5 out of 5
100% buy agian
100% buy agian
cameron s.
Originally posted at
2024-11-13T19:00:00
Rated 5 out of 5
Perfect mount for your DPP!
Perfect mount for your DPP!
I put it on my Mark 5 HD. Could use a slight riser on the DPP but not mandatory and the DPP is perfect for short range quick acquisition 50-200 yards out while the Mark 5 HD is amazing between 300 and 800.
Could not ask for a better set up! Thanks Leupold!!
Former Marine Infantry Squad Leader
Joseph H.
Originally posted at
2024-11-01T20:00:00
Rated 5 out of 5
Awesome accessory.
Awesome accessory.
Donnie H.
Originally posted at
2024-09-12T20:00:00
Rated 4 out of 5
Installer beware
Love the mount fit and finish but take note if using an inch/lb torque wrench. Leupold specs the base to rings at 22 or 25 inch lbs. I used locktite and a Wheeler Fat wrench at 18 lbs and immediately stripped the threads on the ring. Leupolds customer service took care of me and ensured me I wasn't out of spec then sent a replacement. Assuming my torque wrench was out of calibration, I bought a brand new "real avid" brand wrench. Since I had the old ring top I played around with it. Long story short without loctite they strip at 20 in/lbs. I chose to do 13lbs with loctite. Maybe both my wrenches are out of calibration who knows, your mileage may vary.
Ike C.
Originally posted at
2024-09-05T20:00:00
Rated 5 out of 5
Best optics I've ever owned
Best optics I've ever owned by far!
Roger D.
Originally posted at
2024-09-02T20:00:00
Na
Steven W.
Originally posted at
2024-08-16T20:00:00
Rated 5 out of 5
The top plate was slightly
The top plate was slightly loose, so I carefully removed it from the ring, applied a small strip of electrical tape between the two surfaces, and then tightened everything back down. This effectively resolved the issue with the looseness.
Zachary L.
Originally posted at
2024-07-24T20:00:00
Rated 5 out of 5
This ring mount kit was
This ring mount kit was easy to use and super helpful with quickly spotting targets. I just with it was available in FDE.
Jeffrey S.
Originally posted at
2024-05-27T20:00:00
Rated 5 out of 5
IM NOT BIG ON LEAVING
IM NOT BIG ON LEAVING REVIEWS SO HERE GOES. THE RING TOP IS THE EASIEST WAY TO RUN A DELTAPOINT PRO ON TOP OF YOUR OPTIC. I TOOK EXTRA TIME TO LAP THE RINGS AS I HATE THE GAPS OR MARKS ON MY TUBE. IT GIVES YOU THREE OPTIONS TOP CENTER THAT DON'T WORK WITH HIGH TURRENTS OR 45 DEGREE LEFT OR RIGHT. THE MOUNT IS SOLID AND WORTH THE PRICE. THE ONLY IMPROVEMENT I WOULD RECOMMEND IS TO INCLUDE FOUR FILLER 8X40 SCREWS TO PLUG THE UNUSED HOLES IN THE RING TOP IT WOULD KEEP DIRT AND WATER FROM GETTING BETWEEN THE SCOPE TUBE AND RING JUST KEEP THE SCREWS SHORT AND AND EVEN WITH THE RING TOP SO YOU DON'T DAMAGE THE TUBE. THANKS LEUPOLD
JOHN G.
Originally posted at
2024-05-20T20:00:00
Rated 5 out of 5
Hold zero and mounts a
Hold zero and mounts a red dot, what else could you ask
Kyle W.
Originally posted at
2024-04-27T20:00:00
Rated 5 out of 5
Has held zero over a
Has held zero over a few hundred rounds of 6 ARC thus far with an eflx on top
Derek K.
Originally posted at
2024-01-29T19:00:00
Rated 5 out of 5
Does What it Ought
Does what it ought to do. Sturdy, well machined, no burrs or raised spots. Great mount, what more is there to say?
Rusty
Originally posted at
2023-11-20T19:00:00
Rated 5 out of 5
Great product
Great product
Donnie H.
Originally posted at
2019-11-14T19:00:00
Rated 5 out of 5
I bought 2 of them, one on my AR and one on my son's AR
Perfect addition to my AR. With a slight upward movement of the head position you can easily transition from the higher magnification of my Mark 4 rifle scope to the quick acquisition of a close quarters red dot, literally , in the blink of an eye !
Bruce
Originally posted at
