
Orders placed during Passover Holiday (Wed 4/1 after 4PM ET – Thurs 4/9) will ship Fri 4/10. View our holiday shipping schedule.
This item is no longer available.
Review Summary
Accidents happen where life happens. Protect your favorite Adorama products and purchase a protection plan to stay covered from accidental damage, mechanical or electrical failure, and more.
If we can’t fix it, we’ll replace it at no additional cost.
Protect your product from drops, spills, and more.
Enjoy your gear without fear. We have you covered!
When regular use of your product over time results in mechanical or electrical failure.
We will never charge you a deductible after the purchase of a plan.
Our claims process is simple & easy and our customer service team is happy to help.
Adorama Protect powered by Extend is available for purchase to customers in the United States. Not available for purchase Internationally or in U.S. Territories.
Browse our FAQ
3-pin XLR female jack, balanced (or unbalanced) input with 24kOhm differential input impedance, maximum balanced input is +19dBu
Cat 5 8p8c RJ45 female receptacle, distributes balanced line level Floor and Relay audio to another SL Interpreter
3-pin XLR female jack, balanced (or unbalanced) input. Switchable 12VDC simplex power. Variable gain of 58dB, 2.4kOhm balanced input impedance, maximum balanced input is +19 dBu
Stereo 3.5mm TRS phone jack, pink and stereo 3.5mm TRRS phone jack, black, unbalanced (r, s) for electret condenser mics, variable gain of 40dB. Bias is 3.7VDC through 2.7kOhm
3.5mm TRRS phone jack, Tip = Left, Ring 1 = Right, Ring 2 = GND, Sleeve = Mic. 40mW maximum power into 32Ohm stereo headset
3.5mm TRS phone jack, mono or stereo headphone, 8Ohm minimum. 190mW maximum power into 32Ohm stereo headset
3-pin XLR male jack, balanced output. Maximum output is +19dBu into 600Ohm balanced load impedance
Red: RCA jack for recording and CH1 audio, Interpreter audio only, no feedthrough
White: RCA jack for recording CH2 audio
Left and Right rotary, controls headphone volume
Left and right rotary with center detent, controls headphone bass and treble tone levels
Push button, backlit red, mutes left and right mics while pressed
Push button, backlit bright red, activates microphone. Right and left Mic On buttons are inter-locked; Mic can only be turned on if the other is off
Push buttons, backlit blue, select listening language group. Listening modes are either/or: turning one on disables the other
Push button, backlit yellow, selects microphone output language group: light on = CH2 Out, light off = CH1 Out
Rotary gain pots control level of microphone and Floor audio
Slide switch enables 12VDC Simplex power to XLR microphone
Slide switch enables Floor feedthrough to CH1 Out XLR jack
Slide switch enables Floor feedthrough to CH2 Out XLR jack
Slide switch disconnects Chassis and Audio Grounds internal to the console
Green LED on back panel indicates optimal audio output level on Norm Out XLR when blinking
Yellow LED on front panel indicates when CH2 is in use
45Hz to 20kHz, +0/-3dB re: 1kHz with flat bass/treble
<0.5% THD at full power
>82dB at 1kHz
>63dB at 1kHz
Bass: +12dB Boost or -12dB Cut at 100Hz
Treble: +12dB Boost or -12dB Cut at 10kHz
10 x 6.35 x 2.45" / 25.40 x 16.13 x 6.22cm
3.4lbs / 1.54kg
615104257542
The SL Interpreter perfectly completes either the Tourguide 2020 or the Tourguide 1039 portfolio to create a compact, quick to install and easy to use interpretation setup for presentation-style conferences or events alike. The SL Interpreter is a compact and stand-alone audio control center for simultaneous interpretation of one or more languages. It allows one or two interpreters to monitor floor or relay sources, activate microphone inputs and route the interpretation signal to different outputs. Ideal for presentation-style conferences, where a floor and a single relay language are used. Recommended to be used with Sennheiser Tourguide 2020 or 1039.