See Options
2 Year
$499.99
3 Year
$649.99
5 Year
$949.99
Need help? Ask our experts.
Review Summary
Accidents happen. Protect your favorite Adorama products and purchase a protection plan to stay covered from accidental damage, mechanical or electrical failures, and more.
If we can’t fix it, we’ll replace it at no additional cost.
Protect your product from drops, spills, and more.
Enjoy your gear without fear. We have you covered!
When regular use of your product over time results in mechanical or electrical failure.
We will never charge you a deductible after the purchase of a plan.
Our claims process is simple & easy and our customer service team is happy to help.
Adorama Protect powered by Extend is available for purchase to customers in the United States. Not available for international or U.S. territories purchases. Plans on open box items do not cover pre-existing damage.
Adorama Protect plans are available for ABS clients. If you have any questions or require assistanse, please call 800-223-2500
Browse our FAQ
Black
Single Rack Unit
International Desktop Supply
Input: 36 W, 110-240 VAC 50-60 Hz
Output: +48VDC, 0.75A center-positive
Rocker switch with LED
67 dB (typical)
FM Wideband, +50kHz deviation, 50uS pre-emphasis
Selectable, 2.3/2.8 or 3.3/3.8MHz
40 to 16,000Hz, +1 dB, -3dB, electrical response
Less than 2%, electrical response
DSP based; Compression 1:1, 1.5:1, or 2:1; High-pass and low-pass filter frequency control
Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage
Dual IR LED for receiver testing, monitoring, and audio signal testing
2x Combination 3-pin XLR, 1/4" (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power
Included
400 Hz internal test tone selectable as audio input source for setup and diagnostics
Available through embedded website
2x 1/4" headphone jacks on front panel for monitoring CH A and CH B audio inputs
Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission
32 Degree F to 122 Degree F (0 Degree C to 50 Degree C) ambient temperature, non-condensing, non-corrosive atmosphere
CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
19 x 1.75 x 8.2" (48.3 x 4.5 x 20.8cm)
5.2 lbs (2.4kg)
Black
IR Transparent polycarbonate
2.3 MHz and 2.8 MHz IR transmitters
32 Degree F to 122 Degree F (0 Degree C to 50 Degree C)
Up to 15000 sq. ft (1393 sq. m) in single channel mode with IR T2 transmitter
2.3 MHz or 2.8 MHz or stereo
100 Hz to 12 kHz, +/- 3 dB
60 dB at 393.7" (10m)
Volume control thumbwheel
3-position selection switch (2.3 MHz, 2.8 MHz, stereo)
Off/on slider for power
120 dB MAX SSPL90 with 2 cc coupler
3.5mm stereo
EAR 089
CE, RoHS, FCC, Canada, RCM, VCCI, WEEE
LiPo
8 hours
CHG 520
Required, included
Lithium ion
Non-universal
5
1.6 oz (45.36g)
Black
Metal and plastic
120 VAC
100-240V / 12VDC TFP 043
5 Units
Individual Charging Indicators: Red LEDs
WEEE, RoHS, CE, FCC, CANADA, RCM, VCCI
12 x 6.25 x 1.5" (30.48 x 15.87 x 3.81cm)
13.6 lbs (6.17kg)
Black
48 VDC supplied by IR M1 via CAT 5e cable
Up to 18000 sq. feet (1672sq. m) in single channel mode
+48VDC Power, RS-485 communication, and Baseband signals for IR
Transmission are all provided via a single CAT5e cable inserted into an RJ-45 jack from the IR M1.
32 Degree F to 122 Degree F (0 Degree C to 50 Degree C) ambient temperature, non-condensing, non-corrosive atmosphere
CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
7.5 x 1.4 x 3.6" (19.1 x 3.6 x 9.1cm)
12.8 oz (362g)
Black
48 VDC, 0.75A
+48VDC Power, RS-485 communication, and Baseband signals for IR
Transmission are all provided via CAT5e cable's inserted into an RJ-45 jack from the IR M1 and out to the IR E4's
1W
328' (100m)
The IR A4 is not rated for use in plenum spaces and will need to be installed in a plenum box for use in such areas
CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
7.6 x 6.6 x 1.1" (193 x 168 x 28mm)
2.4 lbs (1.09kg)
Commercial-grade, large-area WaveCAST enabled Dante infrared system with IR+ transmitter, 2 emitters and array. Comes with Stethoset Receivers.
- IR+ Control Center with Dante -
The IR+ Control Center provides audio over Wi-Fi and Infrared. Infrared is best used for assistive audio in large spaces, or for secured audio transmission within a room. Connect the IR M1 to a Wi-Fi multicast router or in-house network you can stream audio over Wi-Fi to the Williams AV WaveCAST app
The IR+ Control Center features a distributed infrared emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.
The rack mounted or remotely located IR M1 Control Center comes standard with support for up to four IR emitters. Each emitter runs back to the modulator via a CAT5e cable, providing the audio and power needed to support the remote emitter. Each emitter has a coverage area of 18,000 sq. ft.
This version of the product features Dante.
Note: Firmware updates are currently unable to be completed on Mac computers
- IR+ Emitter -
The IR E4 Emitter transmits the audio input from the IR+ (IR M1). Covering a span of 18,000 sq. ft (1,670 sq. meters), a single emitter can be combined with additional IR E4 emitters to provide extra coverage. Up to four emitters can be stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.
For the IR E4 Emitter to function, it must be connected to the IR M1 modulator. Up to 4 emitters can be connected to the IR M1 directly, and up to 16 emitters can be connected with the use of IR A4 arrays.
Note: The IR E4 is not a stand alone system and requires an IR M1 modulator to function.
- IR+ Emitter Array -
The IR+ features a distributed IR emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.
Up to 16 IR E4 emitters can be connected to an IR M1 modulator with the use of the IR A4 arrays. Each IR A4 array can have up to 4 IR E4's connected.
The IR A4 is not a stand alone system and requires an IR M1 modulator and IR E4 emitter's to function.
- Infrared Stereo Stethoscope Receiver -
The IR RX20 is a comfortable, stereo stethoscope-shaped infrared receiver.
The headset works with all Williams Sound 2.3 or 2.8 MHz infrared systems.
- 5-Bay Charger for IR RX20 -
This multi-unit, drop-in style charger will conveniently charge and store up to 5 Williams AV IR RX20 under-the-chin style infrared receivers. Can daisy chain up to 3 chargers from one power supply. This 6-hour smart charger helps keep your products organized and batteries consistently charged.
Note: Charging specifications are based on Williams Sound, rechargeable internal LiPo battery, BAT 020.
- ADA Wall Plaque -
Let your customers know that an ADA-compliant hearing assistance system is available to them with a Hearing Assistance Available sign.
Elevate visitor awareness of your hearing assistance offerings through the ADA Wall Plaque. Designed for your convenience, the included adhesive and stand offer versatile mounting choices. You can effortlessly hang it on a wall or window using the provided adhesive or use the provided stand to display it on a service counter or desk, ensuring clear communication of your ADA-compliant hearing assistance options available.